Full steam ahead - Scottish distillery with Grundfos
There’s steam and there’s high-quality steam. There are pump solutions and intelligent pump solution...
Most pump failures are caused by human failings in installation or maintenance. But get those right and you can minimise failure risk, extend the pump's useful life, and even increase its efficiency and reliability.
At every stage of a pump’s life – from assembly and installation to repair, preventative maintenance and disassembly – LOCTITE® engineering adhesives and compounds can help prevent pump failures and save money. They can even help restore pumps to “as-new” condition so they don’t have to be scrapped and replaced.
Here are some of the most common reasons for pump failure, and how LOCTITE® can help overcome them.
Air space between the threads of the bearing frame and housing components can lead to oil leakage and ultimately, pump failure.
By using an anaerobic thread sealant – which also stops rust and corrosion in the thread space, and you can stop contaminants from entering the oil. The gland flushing connector is also susceptible to corrosion, but thread sealant will protect this too.
While thread sealant helps prevent loosening of the thread, it also makes a unit easier to disassemble using just normal hand tools.
Less dramatic than an oil leak is oil seepage, from porous areas created during cast parts’ manufacture. A LOCTITE® chemical resistant coating applied to the bearing frame interior during assembly forms an effective seal.
If a threaded assembly can loosen itself, it will. But a thread locker is an easy and effective way to prevent self-loosening – and corrosion – on, for example, frame adapter mounting bolts, pump casing bolts and gland studs.
Couplings can also disengage or be misaligned or damaged. A thread locker will help to keep them stable.
It can also do much more. Apply it to the outside diameter of an oil seal and it will fill small air spaces that could create a leak path.
It can secure a key in a keyway, to prevent keyway wear. And it not only keeps assemblies and couplings together, but can also help you get them apart.
When disassembly is required, anti-seize products also make the engineer’s job easier. Exposed, non-stainless and non-coated metal pump parts (power end bolts, lock nuts, dowel pins) are almost certain to rust. Anti-seize will prevent corrosion and reduce seizure risk.
When a cut gasket relaxes, shrinks, extrudes or breaks, it can lead to a leak. The simple answer is to eliminate cut gaskets altogether by using liquid gasketing adhesive.
In areas such as between the bearing frame and adapter, and between the stuffing box and pump casing, you’ll not only avoid traditional gasket problems, you’ll also seal the air space –helping prevent corrosion.
Air spaces also cause problems for bearings, when rust forms in an air space between the bearing and shaft. And all bearings are prone to fretting or spinning on their shafts or within their housing, leading to damage. A retaining compound not only fills the air space to prevent corrosion, but also prevents bearing spin.
Abrasive slurries, solids, cavitation and chemicals all take their toll on pump casings and impellers. But with the help of LOCTITE®, the pump can still be repaired.
A choice of LOCTITE® metal-filled compounds and wear-resistant putties can rebuild worn cutwaters, wear-ring seats, impeller vane tips and other areas. A topcoat of brushable ceramic then adds a high gloss, low friction finish, so the pump runs as close as possible to its best efficiency.
Epoxies also have a restoration role. Constant pressure and abrasion can wear and damage a shaft, and in time oil seals can even cut a groove. But an epoxy with high compressive strength returns the part to full service, quickly and easily.
With so many different LOCTITE® solutions to help prevent pump failure and optimise pump life, it pays to get advice.
So ERIKS has teamed up with LOCTITE® maintenance experts to run a series of pump repair and rebuild workshops. To find out more, please contact your usual ERIKS Service Centre. Without Fail.
Reliability is a buzzword that is seemingly always on the tip of industry tongues, but it’s clear that businesses need to be more proactive in their attempt to maximise their assets.
In this issue, we look beyond equipment, but at processes, systems, strategy and communication.
Get the latest updates from ERIKS including:
Choose any or all of these via the ERIKS Subscription Centre!
Our Know+How brings together the best of the latest Know+How Hub articles in one easy to digest magazine, covering the following topics:
That's why its the leading magazine for maintenance engineers from ERIKS.
Want Know+How Magazine delivered direct to your door? Visit the ERIKS Subscription Centre to opt-in!
Take a look at our latest updates...
There’s steam and there’s high-quality steam. There are pump solutions and intelligent pump solution...
Looking for a custom Product quote? Need an answer to a Technical question? Looking for Careers/HR support? Want to work with us? Interested in our Digital Trading solutions? Have a finance question? Send us your enquiry and a member of the ERIKS team will be with you quickly.
We strive to deliver exceptional quality service and products. As part of this goal, we encourage customers to submit feedback on their experiences so we can resolve any issues and concerns.
At ERIKS we strive to deliver the best quality service and products. As part of this goal we encourage customers to submit feedback on their experiences so we can resolve any issues and concerns.
Call us: +441215086000